Proceedings
Authors
| Filter results9 paper(s) found. |
|---|
1. Design, Error Characterization And Testing Of A System To Measure Locations Of Fruits In Tree CanopiesMapping the variability of fruit size and quality within tree canopies in commercial orchards is an important tool for implementing precision horticulture. To do so at a reasonably fast rate requires localization technologies that offer sufficient speed and accuracy, at a range long enough to cover entire trees – or several trees at a time. Existing approaches for measuring fruit locations include: manual (centimeter accuracy and measurement time in the order of minutes per... S.G. Vougioukas, F.J. Jimenez, F. Khosro anjom, R. Elkins, C. Ingels, R. Arikapudi |
2. Site Specific Drip FertigationTwo test plots, one from high fertility zone and one from low fertility zone were identified and delineated with the help of GPS for raising the test crop. Soil samples were collected from the experimental sites one month before planting. The samples were analyzed for available N, P and K. Site specific nutrient recommendations were made using the Decision Support System for Integrated Fertilizer Recommendation (DSSIFER) software (Murugappan et al. 2004) for optimum yield.... A.H. V.m. |
3. Development of Real-time Color Analysis for the On- Line Automated Weeding OperationsWeeds compete with the crop for water, light, nutrients and space, and therefore reduce crop yields and also affect the efficient use of machinery. Chemical sprayer is the most popular method to eradicate weeds but has cause hazardous to the environment, crops and workers. A smart sprayer is required to control the usage of chemical weedicides at the optimal level. Thus an on-line automated sprayer is introduced to the Malaysian farmers to locate in the real time environment the existence and... W. Wan ismail, K. Abdul rahman |
4. Evaluation of Strip Tillage Systems in Maize Production in HungaryStrip tillage is a form of conservation tillage system. It combines the benefits of conventional tillage systems with the soil-protecting advantages of no-tillage. The tillage zone is typically 0.25 to 0.3 m wide and 0.25 to 0.30 m deep. The soil surface between these strips is left undisturbed and the residue from the previous crop remain on the soil surface. The residue-covered area reaches 60-70%. Keeping residue on the surface helps prevent soil structure and reduce water loss from the soil.... T. Rátonyi, P. Ragán, D. Sulyok, J. Nagy, E. Harsányi, A. Vántus, N. Csatári |
5. Examining the Relationship Between SPAD, LAI and NDVI Values in a Maize Long-Term ExperimentIn Hungary, the preconditions for the use of precision crop production have undergone enormous development over the last five years. RTK coverage is complete in crop production areas. Consultants are increasingly using the vegetation index maps from Landsat and Sentinel satellite data, but measurements with on-site proximal plant sensors are also needed to exclude the influence of the atmosphere. The aim of our studies was to compare the values measured by proximal plant sensors in the... P. Ragán, E. Harsányi, J. Nagy, T. Ágnes, T. Rátonyi, A. Vántus, N. Csatári |
6. The Spread of Precision Livestock Farming Technology at Dairy Farms in East HungaryDuring the survey, 25 dairy farms were examined in East Hungary in Hajdú-Bihar (H-B) County between 2017 and 2018 by methodical observation and oral interviews with the farm managers, about the spread of Precision Livestock Farming (PLF) technologies. Among Holstein Friesian dairy farms in the County 60% were questioned, and the representativity was above 47 percent ins each size category. Nine precision farming equipment were examined on the farms: milking robot or robotic carousel milking... C. Nándor, T. Rátonyi, E. Harsányi, P. Ragán, Z. Hagymássy, J. Nagy, A. Vántus |
7. Variety Effects on Cotton Yield Monitor CalibrationWhile modern grain yield monitors are able to harvest variety and hybrid trials without imposing bias, cotton yield monitors are affected by varietal properties. With planters capable of site-specific planting of multiple varieties, it is essential to better understand cotton yield monitor calibration. Large-plot field experiments were conducted with two southeast Missouri cotton producers to compare yield monitor-estimated weights and observed weights in replicated variety trials. Two replications... E. Vories, A. Jones, G. Stevens, C. Meeks |
8. Design and Performance Experiment of an Outer Grooved-Wheel Fertilizer Apparatus with the Helical ToothTraditional outer groove-wheel fertilizer apparatus (OGWFA) with the straight tooth exists the problem of breakage and pulsation in the fertilizing process. A new type of OGWFA with the helical tooth has been designed to solve this problem, and the amount of fertilizer can be adjusted. The helix angle of the helical tooth has been optimized by theory analysis and DEM simulation. It reveals that the helix angle should be ranged from 34.4° to 68.8°. The performances of the OGWFA with the... D. Jun, X. Junfang, Z. Wangyuan, W. Qiaohua, D. Youchun, S. Caixia, Z. Zhihui |
9. Impact of Cover Crop and Soil Apparent Electrical Conductivity on Cotton Development and YieldCotton is one of the major crops in the New Madrid Seismic Zone (NMSZ) of the U.S. Lower Mississippi River Valley region. Because cotton production doesn’t leave a lot of crop residue in the field, low soil organic matter levels are common. While the benefits of crop rotation are well known, cotton is often grown year after year in the same fields for economic reasons. Soils in the region are generally quite variable, with areas of very high sand content. Winter cover crops and reduced tillage... E. Vories, K. Veum, K. Sudduth |