Authors
| Filter results12 paper(s) found. |
|---|
1. Application Rate Stability When Implementing Automatic Section Control Technology On Agricultural SprayersAutomatic section control (on and off) technology of sprayer boom sections is an intelligent solution to maximize spray application efficiency during field operations. This technology can reduce over-application of products. Spray controllers available with this technology attempt to maintain the set target rate by adjusting system flow rate based on ground speed and application width. Therefore, as sections are turned on or off, the flow regulating hardware must respond to maintain... A. Sharda, J.D. Luck, J.P. Fulton, S.A. Shearer, S.A. Shearer, D. Mullenix, M. Vanacht |
2. Tip Flow Uniformity When Using Different Automatic Section Control Technologies During Field OperationsAutomatic section control (ASC) technology provides a means to reduce double-coverage and application in unwanted areas thereby leading to input savings and improved environmental stewardship. However, the impact of ASC on spray boom dynamics and tip flow uniformity are unknown. Therefore, a study was conducted to evaluate tip flow rate uniformity and control system response in maintaining target application rates during field operation. Field experiments were conducted using two self-propelled... A. Sharda, J.D. Luck, J.P. Fulton, S.A. Shearer, T.P. Mcdonald, D. Mullenix |
3. Generating Herbicide Effective Application Rate Maps Based On GPS Position, Nozzle Pressure, And Boom Section Actuation Data Collected From Sprayer Control SystemsThe application of pre- and post- emergence burn-down herbicides (i.e., glyphosate) continues to increase as producers attempt to reduce both negative environmental impacts from tillage and input costs from labor, machinery and materials. The use of precision agriculture technologies such as automatic boom section control allows producers to reduce off-target application when applying herbicides. While automatic boom section control has provided benefits, pressure differences across... J.D. Luck, A. Sharda, S.K. Pitla, J.P. Fulton, S.A. Shearer |
4. Effect Of Time Of Application On Spray Coverage Using Solid Set Canopy Delivery SystemPermanent or solid set canopy delivery system can be used for foliar application in tree fruit orchards. The emitters are placed along the tree rows and are very close to tree canopy. During spray application droplets quickly get deposited on tree canopy and coverage of up to 90% could be achieved. However concerns still exist regarding critical time required to achieve target coverage using SSCD system. This knowledge of selecting an appropriate application time could help growers... M. Karkee, Q. Zhang, A. Sharda |
5. sUAVS Technology For Better Monitoring Crop Status For Winter CanolaThe small-unmanned aircraft vehicles (sUAVS) are currently gaining more popularity in agriculture with uses including identification of weeds and crop production issues, diagnosing nutrient deficiencies, detection of chemical drift, scouting for pests, identification of biotic or abiotic stresses, and prediction of biomass and yield. Research information on the use of sUAVS have been published and conducted in crops such as rice, wheat, and corn, but the development of... I.A. Ciampitti, K. Shroyer, V. Prasad, A. Sharda, M.J. Stamm, H. Wang, K. Price, D. Mangus |
6. Selection and Utility of Uncooled Thermal Cameras for Spatial Crop Temperature Measurement Within Precision AgricultureSince previous research used local, single-point measurements to indicate crop water stress, thermography is presented as a technique capable of measuring spatial temperatures supporting its use for monitoring crop water stress. This study investigated measurement accuracy of uncooled thermal cameras under strict environmental conditions, developed hardware and software to implement uncooled thermal cameras and quantified intrinsic properties that impact measurement accuracy and repeatability.... D.L. Mangus, A. Sharda |
7. Site-specific Scale Efficiency Determined by Data Envelopment Analysis of Precision Agriculture Field DataSince its inception and acceptance as a benchmarking tool within the economics literature, data envelopment analysis (DEA) has been used primarily as a means of calculating and ranking whole-farm entities marked as decision making units (DMU) against one another. Within this study, instead of ranking the entire farm operation against similar peers that encompass the study, individual data points from within the field are evaluated to analyze the site-specific technical efficiencies estimated... J.L. Maurer, T.W. Griffin, A. Sharda |
8. On Farm Studies to Determine Seeding Rate in CornSeeding rate (SDR) is one of the most critical production practices impacting productivity and economic return for corn (Zea mays L.) By changing SDRs in different zones within a field, herein termed as site-specific management, better economic results can be produced as the outcome of reducing SDRs in low productivity areas and increasing SDRs under high-yielding environments, relative to the uniform SDR management performed by the producer. The aim of this study was to analyze yield responses... G. Balboa, S. Varela, I. Ciampitti, S. Duncan, T. Maxwell, D. Shoups, A. Sharda |
9. Value of Map Sharing Between Multiple Vehicles Using Automated Section Control in the Same FieldLarge area farms and even moderate sized farms employing custom applicators and harvesters have multiple machines in the same field at the same time conducting the same field operation. As a method to control input costs and minimize application overlap, these machines have been equipped with automatic section control (ASC). Over application is a concern especially for more irregularly shaped fields; however modern technology including automated guidance combined with automatic section control... J. Bennett, C. Wilson, A. Sharda, T. Griffin |
10. Real-time Gauge Wheel Load Variability on Planter with Downforce Control During Field OperationDownforce control allows planters to maintain gauge wheel load across a range of soil resistance within a field. Downforce control is typically set for a target seed depth and either set to manually or automatically control the gauge wheel load. This technology uses load cells to actively regulate downforce on individual row units by monitoring target load on the gauge wheels. However, no studies have been conducted to evaluate the variability in gauge wheel load observed during planter operation... A. Sharda, S. Badua, D. Flippo, I. Ciampitti, T.W. Griffin |
11. Influence of Planter Downforce Setting and Ground Speed on Seeding Depth and Plant Spacing Uniformity of CornUniform seed placement improves seed-to-soil contact and requires proper selection of downforce control across varying field conditions. At faster ground speeds, downforce changes and it becomes critical to select the level of planter downforce settings to achieve the desired consistency of seed placement during planting. The objective of this study was to assess the effect of ground speed and downforce setting on seeding depth and plant spacing and to evaluate the relationship of ground speed... A. Sharda, S. Badua, I. Ciampitti, R. Strasser, T.W. Griffin |
12. Seed Localization System Suite with CNNs for Seed Spacing Estimation, Population Estimation and DoublesProper seed placement during planting is critical to achieve uniform emergence which optimizes the crop for maximum yield potential. Currently, the ideal way to determine planter performance is to manually measure plant spacing and seeding depth. However, this process is both cost- and labor-intensive and prone to human errors. Therefore, this study aimed to develop seed localization system (SLS) system to measure seed spacing and seeding depth and providing the geo-location of each planted seed.... A. Sharda, R. Harsha chepally |